📄 Digital book in PDF · read it on your phone or print it
Contactors, overloads, push-button colours, DOL starters, reversing, star-delta, pump alternation, safe isolation and fault finding. Every topic has its own page: the drawing first, then what you need to remember. 67 illustrated pages.
🔒 Secure checkout · PDF by email · 30-day guarantee
Every page has one large drawing and a box with the terminal numbers, settings and steps you need to know:








Swipe to see more →
These are real pages from the book. The table of contents is the full one: 9 parts and 63 topics.
You're at a pump panel with the drawing taped inside the door, and the customer is waiting to hear why it won't start. Coils, contacts, numbers, and no obvious place to begin.
The books you've tried explain it in paragraphs, often with NEMA ladders at 480 V. Nobody gives you an order to follow, so you jump from line to line and lose the thread.

Here it's one page: the five-step reading order. Supply, power circuit, coil, what energises it, where its contacts act. Five boxes, drawn left to right, the same on every schematic.
The same goes for NO and NC contacts, the 95-96 overload contact, the 13-14 hold-in, the star-delta changeover and safe isolation: each one has its own page.
Next time the drawing is on the door, you read it in order and find the fault without going back to the manual.

Nine parts: the basics before the drawing; symbols and devices; reading any schematic; basic circuits; reversing and timing; star-delta; pumps, fans and compressors; wiring, testing and fault finding; and a practical review. 67 pages, all illustrated.
Think of it this way:
A farm calls: the water tank hasn't filled overnight and the pump sits there doing nothing. You open the panel and need to know which float, which contact and which coil.
In the book you open the tank-filling page and see the power and control circuits side by side, the floats drawn at rest, and the LOW float that starts, the HIGH float that stops and the 13-14 contact that holds the coil in between.

The same with forward-reverse, the star-delta changeover, setting the overload, safe isolation and a contactor that chatters: each one on its own page.
Motor Control Circuits Illustrated is 9 parts and 63 topics, all drawn, with 20 circuits shown as schematic, wiring and sequence, and a pre-energising checklist at the end.
What you see drawn, you don't have to memorize.
Why IEC and not NEMA, 400/230 V three-phase, the motor nameplate, star and delta in the terminal box, full-load and starting current, power and control side by side.
NO and NC contacts, terminal numbers, the contactor, the overload relay, MPCBs and fuses, the isolator, push-button and lamp colours, timers, the control supply and device letters.
The five-step reading order, current paths and column numbers, cross-references, wire numbers and terminal strips, the rest state and the sequence of operation.
Eight circuits: DOL start-stop with hold-in, run and trip lamps, two-place control, jog, hand-off-auto, single-phase motor, emergency stop and no restart after a power cut.
Swapping two phases, forward-stop-reverse, direct reversal, interlocks, a gate with limit switches, timed start and extract fan run-on.
Why star-delta, the power circuit, the control and sequence, setting the overload, changeover time, and star-delta against a soft starter or drive.
Tank filling, sump emptying, duty and standby alternation, high-level alarm, compressor on a pressure switch, sequence start, thermistor and phase-failure relays.
Safe isolation, wiring from the schematic, insulation and winding resistance, rotation check and four faults: chatter, a tripping overload, no start and a humming motor.
The pre-energising checklist, the most frequent wiring mistakes, the reading order on one page and handing over the job.
At the end of the book: 20 circuits, each as schematic, wiring drawing and sequence of operation, plus a pre-energising checklist.

Trace 30 control schematics line by line and check your answer on the next page, until reading a new drawing becomes routine.

Every IEC symbol, device letter and push-button colour on printable cards to keep in the van and check at a glance on site.
📄 This is a digital PDF book sent to your email: nothing is printed or shipped.
PDF by email: We email you Motor Control Circuits Illustrated as a PDF, together with the two free books. It's a single payment: no installments, no extra charges.
You get the symbols, the devices and the five-step reading order, one page each, before your first panel.
You open the circuit you need, DOL, reversing or star-delta, and see the schematic, the wiring and the sequence.
You keep the fault pages and the pre-energising checklist to hand, and check terminal numbers at a glance.
📄 This is a digital PDF book sent to your email: nothing is printed or shipped.
Try Motor Control Circuits Illustrated for 30 days, bonus books included.
We refund everything if the file won't open, if the book isn't what you see here, if you were charged twice or if the email doesn't arrive. Just email us.
You pay once. No subscriptions.
Yes. It assumes you already do installation work to BS 7671 and starts from what's new in motor circuits: IEC symbols at 400/230 V, 50 Hz (no NEMA, no 480 V), contactors, overloads and the order to read a schematic.
From BS 7671 (the edition in force when the book was checked, with its amendments), BS EN 60204-1, BS EN 60947-4-1, IEC 60617 symbols, BS EN 60445 terminal markings and HSE guidance GS38. Symbols, terminal numbers and the circuits themselves come from the IEC/EN standards, not from BS 7671. Everything is explained with our own drawings; no text or tables are reproduced from the standards.
No. It's an independent illustrated guide, not affiliated with or endorsed by the IET, BSI, IEC or HSE.
No. It's a drawn reference to understand and revise. It doesn't replace training, supervised work, the manufacturer's instructions or BS 7671 itself.
No. The 30 circuits in the workbook are written for this book. It isn't exam preparation and it doesn't come with a certificate or qualification: it's for reading and wiring real panels.
As a PDF by email, to the address you enter at checkout.
No. It's a one-off payment, with no subscription.
Yes. It's a PDF you can print at home or at a print shop and keep in the van.
You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.
No more rereading without it sticking.
The DOL hold-in circuit: you see it drawn and that's it.
You turn up to the job knowing where everything is.
Drawings make studying faster.
The book is right below.
One-time payment: US$ 27 · Guarantee: 30 days · PDF by email
YES, I WANT MOTOR CONTROL CIRCUITS ILLUSTRATED FOR US$ 27📄 This is a digital PDF book sent to your email: nothing is printed or shipped.